tel:
86-635-2998833

address :  No.69,Huaihe Road,Liaocheng 
city,High-tech zone,Shandong Province,China

Copyright: Liaocheng YANGFINE Machinery Co.Ltd.    ICP: 鲁ICP备05008265号-1   Powered by  www.300.cn 

Zip code :  255000

Telephone :  86-0635 - 2998833/2921122 

Fax :  86-0635 - 2998855

mailbox :  bjcompany@vip.sina.com

  • 1

    1

  • 2

    2

  • 3

    3

>
news
>
>
How to adjust the small excitation force of the vibration motor

How to adjust the small excitation force of the vibration motor

Classification:
Industry
Release time:
2018/12/30

Centrifugal force is too small vibration motor vibration machine is a lot of users often encounter and how to solve this problem . In fact, the factory vibration motor excitation force were raised to 80% , it takes seaborne ( export ) Centrifugal force raised to 0% . When used according to the following steps to adjust :

1, the horizontal vibration motor :

( 1 ) , loosen the screws fastening the protective cover , remove both ends of the shield ;

( 2 ) , the exciting force is less than MV50-2, MV50-4, MV50-6, vibration motor MV30-8 (not included in this four specifications ) , the outer eccentric adjustable block , surface mounted marked Max.centrifugal force percentage scale , the eccentric block is fixed blocks are pressed using the fastening bolts on the motor shaft . Both end surfaces of the shaft engraved baseline. Loosen the outer sides of eccentric bolts , with the outer sides of the eccentric rotation , so that the shaft groove aligned exciting force eccentric ruler engraved lines on the outside , to the required excitation force , tighten the outer eccentric block bolts , fitted with protective cover ;

( 3 ) Centrifugal force is greater than or equal to MV50-2, MV50-4, MV50-6, the vibration motor MV30-8 ( containing the four specifications ) , the outer eccentric fixed block fixed to the rotary shaft with a key , not rotation. The adjustable eccentric block , with the outer surface excitation force marked the biggest percentage scale , using the fastening bolts pressed on the motor shaft . Loosen the sides of the eccentric bolts , on both sides of the eccentric rotating in the same direction , so that the exciting force eccentric ruler engraved lines on the alignment of the outer eccentric slit , to the required excitation force , tighten the eccentric bolts , fitted with protective cover ;

Note : Except for special applications , the position of the motor shaft at both ends of the eccentric vibration must correspond to both ends of the eccentric set percentage must be equal , otherwise vibration motor generates a huge mistake to exciting force , vibration motor mechanical damage .

2, the vertical vibration motor :

( 1 ) exciting force adjustment: Remove the additional block bolts to adjust the exciting force by increasing or decreasing the number of additional blocks ;Adjusting 

( 2 ) the eccentric angle : the eccentric block is a fixed block , the next block is an adjustable eccentric , the use of fastening bolts are pressed against the motor shaft . Engraved on the surface of the shaft ends of the baseline , with the outer surface under eccentric ruler marked rotation angle , spin Panasonic eccentric bolts , turn the eccentric block , so that the eccentric angle on the basis of the scale engraved reticle alignment of the shaft lines, adjusted to the desired angle and tighten the lower eccentric bolts ; For adjusting the eccentric angle , but also can adjust the corresponding method .

3 Connect the power

A vibration motor cables due to withstand vibration , so should use heavy-duty four -core cable , do not allow a sudden bend near the cable exit, have a 8-9 times greater than the outer diameter of the cable bend radius , and then the cable is not fixed to a stationary moving machine or frame . Its distance is about 0.6 meters to 0.9 meters. In the cable clamp should be fixed at the pad with soft insulating material , in order to avoid friction damage to the cable. Four core cable ground wire , one end of the junction box is connected to the grounding screw , the other end must be grounded . Small models vibration motor, chassis no junction box, using heavy three-core cable connection directly from inside the motor. In the vicinity of the motor foot with a ground screw , must be grounded when in use.

Note: The vibration motor cable outlet for the wearing parts, often due to vibration friction damage, leading to motor phase operation, damage to the motor . Users should always check the condition of the cable , should be replaced if worn the same type cable.

Try to do once every three months plus oil , if used for too long ( discretionary add )

NEWS